MCP9808T-E/MS【PDF 19/52 页】IC TEMP SENSOR DGTL I2C 8MSOP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录44

15页 16页 17页 18页 [19页]20页 21页 22页 23页

?2011 Microchip Technology Inc.

DS25095A-page 19

MCP9808

bit 7

Crit. Lock: T

CRIT

Lock bit

0 = Unlocked. T

CRIT

1 = Locked. T

CRIT

When enabled, this bit remains set to 1 or locked until cleared by an internal Reset (Section 5.3

Summary of Power-on Default).

This bit can be programmed in Shutdown mode.

bit 6

Win. Lock: T

UPPER

and T

LOWER

Window Lock bit

0 = Unlocked; T

UPPER

and T

LOWER

registers can be written (power-up default)

1 = Locked; T

UPPER

and T

LOWER

registers can not be written

When enabled, this bit remains set to 1 or locked until cleared by a Power-on Reset (Section 5.3

Summary of Power-on Default).

This bit can be programmed in Shutdown mode.

bit 5

Int. Clear: Interrupt Clear bit

0 = No effect (power-up default)

1 = Clear interrupt output; when read, this bit returns to 0

This bit can not be set to 1 in Shutdown mode, but it can be cleared after the device enters Shutdown

mode.

bit 4

Alert Stat.: Alert Output Status bit

0 = Alert output is not asserted by the device (power-up default)

1 = Alert output is asserted as a comparator/Interrupt or critical temperature output

This bit can not be set to 1 or cleared to 0 in Shutdown mode. However, if the Alert output is config-

ured as Interrupt mode, and if the host controller clears to 0, the interrupt, using bit 5 while the device

is in Shutdown mode, then this bit will also be cleared 0.

bit 3

Alert Cnt.: Alert Output Control bit

0 = Disabled (power-up default)

1 = Enabled

This bit can not be altered when either of the Lock bits are set (bit 6 and bit 7).

This bit can be programmed in Shutdown mode, but the Alert output will not assert or deassert.

bit 2

Alert Sel.: Alert Output Select bit

0 = Alert output for T

UPPER

, T

LOWER

and T

CRIT

(power-up default)

1 = T

> T

CRIT

only (T

UPPER

and T

LOWER

temperature boundaries are disabled)

When the Alarm Window Lock bit is set, this bit cannot be altered until unlocked (bit 6).

This bit can be programmed in Shutdown mode, but the Alert output will not assert or deassert.

bit 1

Alert Pol.: Alert Output Polarity bit

0 = Active-low (power-up default; pull-up resistor required)

1 = Active-high

This bit cannot be altered when either of the Lock bits are set (bit 6 and bit 7).

This bit can be programmed in Shutdown mode, but the Alert output will not assert or deassert.

bit 0

Alert Mod.: Alert Output Mode bit

0 = Comparator output (power-up default)

1 = Interrupt output

This bit cannot be altered when either of the Lock bits are set (bit 6 and bit 7).

This bit can be programmed in Shutdown mode, but the Alert output will not assert or deassert.

CONFIG: CONFIGURATION REGISTER (?/SPAN> ADDRESS 0000 0001b)

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式